Extron electronic Network Card AAP 102 FSR User Manual

RGB 460xi /472xi FSR Series and  
AAP 102 FSR Installation Guide  
FSR Floor box-Mounted Interface  
Extron Electronics, USA  
1230 South Lewis Street  
Anaheim, CA 92805  
USA  
714.491.1500  
Fax 714.491.1517  
Extron Electronics, Europe  
Beeldschermweg 6C  
3821 AH Amersfoort  
The Netherlands  
+31.33.453.4040  
Fax +31.33.453.4050  
Extron Electronics, Asia  
135 Joo Seng Road, #04-01  
PM Industrial Building  
Singapore 368363  
+65.6383.4400  
Fax +65.6383.4664  
Extron Electronics, Japan  
Daisan DMJ Building 6F  
3-9-1 Kudan Minami  
Chiyoda-ku, Tokyo 102-0074 Japan  
+81.3.3511.7655  
68-636-05 Rev. A  
Printed in the USA  
06 03  
Fax +81.3.3511.7656  
© 2003 Extron Electronics. All rights reserved.  
 
Table of Contents  
About this Guide....................................................................... 1  
Installation Overview............................................................. 1  
Installation Instructions ....................................................... 2  
Preparing the site and cables................................................... 2  
Mounting the interface or adapter plate to the floorbox .... 3  
Specifications ............................................................................. 4  
Included Parts............................................................................. 5  
Accessories................................................................................... 5  
Cables ............................................................................................. 6  
Male-to-male VGA cables ........................................................... 6  
Male-to-male 90° VGA cables .................................................. 6  
Adapter kits .............................................................................. 6  
High resolution cables .............................................................. 6  
All trademarks mentioned in this manual are the properties of their respective owners.  
68-636-05 Rev. A  
Printed in the USA  
06 03  
RGB 460xi/472xi/AAP 102 FSR Series • Table of Contents  
i
 
Table of Contents, cont’d  
About this Guide  
This guide contains instructions for mounting two different  
®
Extron computer interfaces and an adapter plate into FSR floor  
boxes. The interfaces are standard RGB 460xi series and RGB  
472xi series interfaces tailored to fit the FSR floor box.  
The AAP 102 FSR adapter plate is a blank faceplate for the FSR  
floor box, to which any standard Extron AAP (Architectural  
Adapter Plate) can be mounted.  
In this guide, the terms “FSR interface” and “Interface” are used  
interchangeably.  
For information about operating and wiring the interface, refer  
to the RGB 400xi Series User Manual, Part #68-542-01, or the RGB  
470xi Series User’s Manual, Part #68-661-01, depending on the  
specific product you are using.  
Installation Overview  
Installation and service must be performed by  
authorized personnel only. These products must be  
used with UL approved electrical boxes.  
CAUTION  
Install the interface or adapter plate as follows:  
Turn all of the equipment off. Make sure that the  
computer, the interface, and the output devices (projector/  
monitor, speakers) are all turned off and disconnected  
from the power source.  
1
Select the installation location and install the electrical  
floor box. Refer to the documentation that was included  
with the floor box.  
2
3
4
Route the cables that connect to the rear of the interface (or  
the AAP(s) to be installed in the AAP 102 FSR adapter  
plate).  
Set the gain and DIP switches (or the switch(es) on the rear of  
the AAP(s) to be installed in the AAP 102 FSR adapter plate).  
Refer to the RGB 400xi Series User Manual, Part #68-542-01, the  
RGB 470xi Series User Manual, Part #68-661-01.  
For the AAP 102 FSR adapter plate only, secure the  
AAP(s) to the front of the faceplate.  
5
6
Connect the video, audio, and power cables to the rear of the  
device. Refer to the RGB 400xi Series User Manual, Part #68-  
542-01, the RGB 470xi Series User Manual, Part #68-661-01.  
Connect power cords and turn on the projector or monitor  
and audio device, the interface, and the computer.  
7
ii  
RGB 460xi/472xi/AAP 102 FSR Series • Table of Contents  
RGB 460xi/472xi/AAP 102 FSR Series • Installation Guide  
1
 
Installation, cont’d  
The picture should now appear, and sound should be  
8
audible. If not, ensure that all devices are plugged in and  
receiving power. Check the cabling and switch settings,  
and make adjustments as needed.  
Plastic Filler Strip  
(optional)  
T
IF  
SH  
.
H
R
P
O
IT  
N
O
X
M
A
MIN/M  
T
U
IN  
Disconnect power from all the devices.  
R
9
O
IT  
N
O
M
IO  
D
O
N
AU  
R
O
IT  
N
O
M
RGB 460xi FSR  
Mount the interface or adapter plate into the floor box.  
See Mounting the interface or adapter plate to the floor box in  
this manual.  
10  
RGB 460xi FSR  
Mounting Plate  
Restore power to the devices.  
11  
Installation Instructions  
Installation  
Cable  
The interface must be installed into an  
CAUTION  
Underwriters Laboratories (UL) approved FSR  
electrical floor box. The floor box is not included  
with the interface; the installer is responsible for  
obtaining and installing the box.  
Preparing the site and cables  
Choose a location that allows cable runs without interference.  
Allow enough depth for both the floor box and the cables. You  
need to run the conduit (if required by local code) and cables  
under the floor before installing the interface.  
The installation must conform to national and local electrical  
codes and to the interface’s size requirements.  
1.  
2.  
3.  
Install the floor box in accordance with the documentation  
that accompanied the box.  
FSR Box  
Feed cables through the floor box punch-out holes, and  
secure them with cable clamps to provide strain relief.  
Screw  
Exposed cable shields (braids or foil) are potential sources  
of short circuits. Trim back and/or insulate shields with  
heat shrink, or ground the shield to the box (figure 1).  
Braided Shield  
Figure 1 — Securing the RGB 460xi FSR adapter  
plate to the floor box and grounding the braided  
shield  
To prevent short circuits, the outer foil shield can be  
cut back to the point where the cable exits the cable  
clamp. Both braided and foil shields should be  
connected to an equipment ground at the other end  
of the cable.  
CAUTION  
5.  
Secure the interface or adapter plate to the floor box with  
the screws provided. See Mounting the interface or adapter  
plate below.  
4.  
Set the gain and DIP switches and cable and test the device  
before securing it into the floor box. The switches and  
cables will be inaccessible after installation.  
Mounting the interface or adapter plate to the  
floor box  
Refer to the RGB 400xi Series User Manual, Part #68-542-01  
or the RGB 470xi Series User Manual, Part #68-661-01 for  
additional information.  
1.  
Disconnect the power supply to remove power from the  
interface.  
2.  
If installed, remove the floor box’s top panel and trim frame.  
2
RGB 460xi/472xi/AAP 102 FSR Series • Installation Guide  
RGB 460xi/472xi/AAP 102 FSR Series • Installation Guide  
3
 
Installation, cont’d  
3.  
Place the interface or adapter plate through the opening in  
Temperature/humidity .............. Storage -40° to +158°F (-40° to +70°C) /  
10% to 90%, non condensing  
the floor and into the floor box. Take care not to damage  
the cables, which lay behind the interface in the bottom of  
the box.  
Operating +32° to +122°F (0° to +50°C) /  
10% to 90%, non condensing  
Rack mount................................... No, but FSR floor box mountable  
Enclosure type.............................. Metal  
Enclosure dimensions  
4.  
Mount the interface or adapter plate(s) to the floor box  
with the included machine screws.  
Install the faceplate with four  
machine screws (included).  
RGB 460xi/472xi FSR  
Plate.......................... 4.5" H x 3.6" W (11.4 cm H x 9.1 cm W)  
Back enclosure ........ 2.7" H x 3.3" W x 1.1" D  
(6.9 cm H x 8.4 cm W x 2.8 cm D)  
(Depth excludes front panel connectors  
and controls.)  
AAP 102 FSR .................... 4.5" H x 3.6" W (11.4 cm H x 9.1 cm W)  
Specifications are subject to change without notice.  
Included Parts  
These items are included in each order for the indicated interface:  
Included parts  
Part number  
60-373-40  
60-515-40  
60-301-40  
70-055-01  
68-542-01  
68-661-01  
100-216-01  
RGB 460xi FSR, black  
Install the plastic filler  
strips (optional).  
RGB 472xi FSR, black  
AAP 102 FSR  
Figure 2 — AAP 102 FSR, RGB 460xi FSR, and RGB  
472xi FSR installed  
12VDC, 1.0A external power supply kit  
RGB 400xi Series User’s Manual  
RGB 470xi Series User’s Manual  
Plastic filler strip  
5.  
If necessary, install a plastic filler strip (included with the  
interface or adapter plate) to fill the gap when the devices  
are installed in either end position (right or left).  
RGB 400xi FSR Series Installation Guide  
6.  
Install the floor box’s top panel and trim frame.  
Reconnect the power supply.  
7.  
Accessories  
Specifications  
Accessories  
Part number  
10-306-01  
26-340-01  
26-340-02  
26-287-01  
26-173-01  
26-397-01  
This guide shows power requirements and physical  
3.5 mm stereo plug  
Mac/VGA adapter  
Mac HV/VGA adapter  
Mac 35/VGA 6’ adapter  
SY VGA/XGA adapter  
SY 15 HDM RGBHVF  
specifications only. For electrical and functional specifications,  
refer to the RGB 400xi Series User Manual, Part #68-542-01 or the  
RGB 470xi Series User’s Manual, Part #68-661-01, depending on  
the specific product you are using.  
General  
Power............................................. 12VDC, 0.42 A, 5 watts, external (the  
power supply is included.)  
4
RGB 460xi/472xi/AAP 102 FSR Series • Installation Guide  
RGB 460xi/472xi/AAP 102 FSR Series • Installation Guide  
5
 
Installation, cont’d  
Cables  
Male-to-male VGA cables  
Part number  
26-238-01  
VGA M6’ MHR  
VGA M3’ MHRA (with audio)  
VGA M6’ MHRA (with audio)  
VGA M12’ MHRA (with audio)  
26-490-01  
26-490-02  
26-490-03  
Male-to-male 90° VGA cables  
Part number  
VGAM 90 MHRA 6’ (with audio)  
26-510-02  
Adapter kits  
Part number  
Mac 15-pin HD F adapter cable kit w/audio  
70-156-01  
13W3 15-pin HD F adapter cable kit w/audio 70-157-01  
High-resolution cables  
BNC-5-3’HR  
Part number  
26-260-15  
26-260-01  
26-260-02  
26-260-03  
26-260-04  
26-260-16  
26-260-05  
26-378-01  
26-378-02  
26-378-03  
26-378-04  
26-378-05  
26-378-06  
26-378-07  
BNC-5-6’HR  
BNC-5-12’HR  
BNC-5-25’HR  
BNC-5-50’HR  
BNC-5-75’HR  
BNC-5-100’HR  
BNC-5-3’HRP (plenum)  
BNC-5-6’HRP (plenum)  
BNC-5-12’HRP (plenum)  
BNC-5-25’HRP (plenum)  
BNC-5-50’HRP (plenum)  
BNC-5-75’HRP (plenum)  
BNC-5-100’HRP (plenum)  
Bulk installation cable  
(14-conductor, non-plenum), 500’ HR  
22-120-02  
22-111-03  
Bulk installation cable  
(17-conductor, plenum), 500’ HR  
6
RGB 460xi/472xi/AAP 102 FSR Series • Installation Guide  
 

Echo Paint Sprayer MS 20H User Manual
Eclipse Fujitsu Ten Car Stereo System CD3424 User Manual
Estate Dishwasher TUD4700W User Manual
Exido Styling Iron 235 020 User Manual
Extron electronic Switch GB 190F User Manual
Fostex Printer VF 08 User Manual
Frigidaire Range 316135921 User Manual
GE Clothes Dryer UPVH880 User Manual
GE Washer Dryer WSM2400L User Manual
Gitzo Camcorder Accessories GT2531EX User Manual