Extron electronic Network Card 68 1405 01 User Manual

AVTracRough-In Adapter Installation Guide  
This adapter is designed for installation in new stud wall  
constructions, prior to installing the gypsum board walls  
(drywall).  
(2) Masonry  
Screws  
1. Determine where AVTrac will abut the wall. (See the  
AVTrac Installation Guide [part number 68-1405-01] for  
factors that must be considered before installation.)  
Cut out a section of the wall base stud that is 4”  
(10.1 cm) wide and align the front edge of the adapter  
base with the front edge of the wall base stud (see the  
figure at right).  
Rough-In Adapter Base  
(Front edge is level with  
wall base stud.)  
2. Mark the position of the holes in the adapter base,  
and drill at least two holes into the  
Dry Wall  
Wall Base Stud  
concrete 5/32” (0.4 cm) diameter and 1 1/2” (3.8 cm) deep. Secure  
the adapter to the floor with the provided masonry screws.  
4.0"  
3. Cut a notch 1.5” (3.8 cm) high x 4” (10.1 cm) wide  
in the bottom edge of the drywall and place the  
drywall over the rough-in adapter with the top edge  
of the notch resting on top of the adapter’s front  
support. Secure the drywall to the wall frame (see  
the figure at left).  
1.5"  
Rough-In Adapter  
Front Support  
4. Install the AVTrac system. For complete information  
about installing the AVTrac system, consult the  
AVTrac Installation Guide.  
AVTracWall Trim Plate Installation Guide  
The wall trim plate is a finishing plate that compensates  
for any overcuts to the existing gypsum wall during  
AVTrac intstallation.  
Wall Trim Plate  
Install the trim ring in place of, or behind, existing wall  
base trimmings as follows:  
1. Install the AVTrac system, as described in the AVTrac  
Installation Guide (part number 68-1405-01).  
2. Before snapping the cover track in place and  
covering the track with a carpet or rubber strip, place  
the trim plate against the wall so that it is seated on  
the AVTrac, covering the overcut hole in the wall.  
3. Mark the position of the two holes in the trim ring on  
the wall and, using the screws provided, secure the  
trim plate to the wall.  
4. Snap the cover track in place and cover the track  
and ramps with carpet, as described in the AVTrac  
Installation Guide (part number 68-1405-01). If  
required, trim the wall baseboard to fit snugly  
around the track and attach it to the wall, over the  
trim plate.  
68-1603-01  
Extron Electronics, USA  
800.633.9876 714.491.1500  
FAX 714.491.1517  
Extron Electronics, Europe  
+800.3987.6673 +31.33.453.4040 +800.7339.8766 +65.6383.4400  
FAX +31.33.453.4050 FAX +65.6383.4664  
Extron Electronics, Asia  
Extron Electronics, Japan  
+81.3.3511.7655  
FAX +81.3.3511.7656  
Rev A  
06 08  
 

Edelbrock Automobile Parts R09392S User Manual
Exido Kitchen Grill 243 045 User Manual
Exmark Lawn Mower 4500 759 Rev A User Manual
Extron electronic DJ Equipment MGP 464 User Manual
EZQuest DVD Player DVD Duplication User Manual
Fisher Price Motorized Toy Car B3162 User Manual
Fisher Weather Radio 244EH User Manual
Fluke Thermometer ESA612 User Manual
GE Oven JKS10DP User Manual
Global Machinery Company Tiller DEC003AC User Manual