Installation Guide
DVI Output Card
Digital Visual Interface Card for ISS 108/408 and ISM 482
68-761-01 Rev. B
01 09
Installation, cont’d
5
Lift cover straight up.
3
Remove (16)
screws.
Remove top two
front panel screws.
4
Fan Connectors:
DVI card socket J14
6
J8 and J13.
J13
B
J8
8
V
/H
H
7
/H
H
6
S
T
5
U
P
N
I
4
3
B
2
G
B
B
1
G
B
H
/
H
B
H
H
B
H
/
H
G
B
H
/
H
H
/
H
8
H
/
H
7
H
/
H
Hz
50/60
MAX.
1.2A
H
/
H
240
-
0
0
4
1
3
1
Figure 1 — Removing the switcher cover
DVI Output Card Installation
2
Installation, cont’d
DVI Output Card Installation
Install the DVI output card in the switcher as follows:
W
Changes to electronic components must be performed by
authorized service personnel only.
W
To prevent electric shock, always unplug the switcher
from the AC power source before opening the enclosure.
1.
Locate the DVI output card connector opening on the rear
panel and the DVI output card socket J14 on the left rear
portion of the main circuit board, as viewed from the front
(figure 2).
Rear Panel
DVI Output Card
Connector Opening
DVI Output Card
Socket J14 on
Main Circuit Board
Figure 2 — DVI output card connector opening and
socket J14
DVI Output Card Installation
3
Installation, cont’d
2.
3.
4.
If the rear panel DVI connector opening is covered, remove the
two screws that secure the cover to the back panel and remove
the cover.
Position the DVI card above J14 with the DVI connector facing
toward the rear of the switcher. Ensure the pins on the DVI
card properly align with the J14 socket to prevent bending.
Carefully insert the DVI board 45-pin connector into socket J14
on the main circuit board (figure 3).
DVI Output Card
DVI Connector
DVI Output Card
DVI Output Card
Mated to the
Main Board via
Socket J14
Figure 3 — Output DVI board installation
5.
Secure the DVI card to the rear panel with the two screws
provided in the kit.
C Carefully inspect the pins to be certain all are properly seated
in the socket before proceeding. The board connector should
have all pins inserted the same depth.
DVI Output Card Installation
4
Installation, cont’d
Closing the Switcher
1.
Reconnect the two fan power cords to connectors J8 and J13 on the
main board. It does not matter which fan is connected to which
connector.
2.
3.
Replace the top cover on the switcher.
Fasten it with the screws that were removed in "Opening the
Switcher", step 3 and step 4.
4.
Reinstall the switcher and reconnect all cables.
Extron USA - West Extron USA - East Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Middle East
Headquarters
+800.633.9876
+800.3987.6673
+800.7339.8766
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
+971.4.2991800
+971.4.2991880 FAX
Inside USA / Canada Only
Inside Europe Only
Inside Asia Only
Inside China Only
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
+86.21.3760.1568
+86.21.3760.1566 FAX
+1.714.491.1500
+1.714.491.1517 FAX
© 2009 Extron Electronics. All rights reserved.
|