Product Category
XTP T HDMI and XTP R HDMI • Setup Guide
This guide provides instructions for an experienced installer to install and connect the Extron XTP T HDMI transmitter and XTP R HDMI receiver.
c
a b
d
e f g
Transmitter Connections
Receiver Connections
a DC power connector
b HDMI input connector
h DC power connector
i XTP input connector
SIG
LINK
INPUTS
POWER
12V
AUDIO
ON
OVER XTP
AUDIO
L
R
1.0
A
MAX
RS-232
IR
RESET
OFF
HDMI
LOOP-THRU
+
−
+
−
Tx Rx
G
Tx Rx
XTP OUT
LAN
c HDMI Loop-thru connector j LAN connector
d Analog audio input connector k RS-232/IR Over XTP connector
XTP T HDMI Rear Panel
e RS-232/IR Over XTP
l HDMI output connector
m Analog audio output connector
n S/PDIF audio output connector
o Relay connectors
h
k
i j
l m n o
connector
f XTP output connector
g LAN connector
OUTPUTS
RELAYS
SIG
LINK
POWER
12V
OVER XTP
AUDIO
AUDIO
ON
1
2
L
R
RS-232
IR
1.0
A
MAX
RESET
OFF
Tx Rx
G
Tx Rx
+
-
+
-
HDMI
LAN
S/PDIF
XTP IN
Installation
XTP R HDMI Rear Panel
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the transmitter and receiver as required.
Step 2 — Connecting inputs
a. Connect a digital video source to the female HDMI connector of the XTP T HDMI (see babove). It can accept HDMI, DVI (with an
appropriate adapter), or DisplayPort video signals.
NOTES:
•
•
Use an Extron LockIt® Locking Bracket to secure HDMI cables to the connectors.
Video input from a DisplayPort source must be a dual mode DisplayPort source.
b. Connect a digital video display to the HDMI loop-thru connector on the transmitter to locally display the input source. Displays that are not
HDCP compliant display a green screen when HDCP encrypted content is sent to them (see cabove).
c. Connect balanced or unbalanced stereo audio to the
Tip
Tip
Sleeve
Tip
Ring
Sleeves
Tip
3.5 mm, 5-pole captive screw connector (see dabove).
Sleeve
Ring
Step 3 — Connecting Throughput Devices
Do not tin the wires!
a. Connect a twisted pair cable between the XTP connectors on
the transmitter and receiver (see fand iabove).
Balanced Stereo Input
Unbalanced Stereo Input
Pins:
12345678
ATTENTION:
network.
Do not connect these connectors to a computer data or telecommunications
TIA/EIA T 568 B
Pin Wire Color
The XTP T HDMI and XTP R HDMI are compatible with CAT 5e, 6, 6a, and 7 shielded twisted pair
(F/UTP, SF/UTP, and S/FTP) and unshielded twisted pair (U/UTP) cable. Extron recommends using
the following practices to achieve full transmission distances up to 330 feet (100 m) and reduce
transmission errors.
1
2
3
4
5
6
7
8
White-orange
Orange
White-green
Blue
z
Use Extron XTP DTP 24 SF/UTP cable for the best performance. If not using XTP DTP 24
cable, at a minimum, Extron recommends 23 AWG, solid conductor, STP cable with a minimum
bandwidth of 400 MHz.
White-blue
Green
z
z
Terminate cables with shielded connectors to the TIA/EIA T 568 B standard.
White-brown
Brown
Limit the use of more than two pass-through points, which may include patch points, punch
down connectors, couplers, and power injectors. If these pass-through points are required, use
CAT 6 or 6a shielded couplers and punch down connectors.
Insert Twisted
Pair Wires
NOTE: When using CAT 5e or CAT 6 cable in bundles or conduits, consider the following:
•
•
•
•
Do not exceed 40% fill capacity in conduits.
Do not comb the cable for the first 20 m, where cables are straightened, aligned, and secured in tight bundles.
Loosely place cables and limit the use of tie wraps or hook and loop fasteners.
Separate twisted pair cables from AC power cables.
Signal LED — Lights on the transmitter when it is transmitting a video signal or a test pattern. Lights on the receiver when it receives an
active XTP input signal from the transmitter.
Link LED — Lights yellow when a valid link between an XTP input and output is established.
1
|