Extron electronic Computer Accessories 330 D User Manual

DTP DVI 230 D and HDMI 230/330 D • Setup Guide  
This setup guide provides instructions for an experienced installer to set up and operate the  
Extron DTP DVI 230 D and DTP HDMI 230 and 330 D extenders.  
INPUTS  
LOCAL OUT  
INPUTS  
DVI-D  
DDC  
ROUTE  
REMOTE  
OVER DTP  
RS-232  
Tx Rx  
IR  
RS-232  
IR  
ON  
AUDIO  
AUDIO  
1
2
G
Tx Rx  
Tx Rx  
G
Tx Rx  
LOCAL  
DTP DVI 230 D Tx  
DTP HDMI 230/330 D Tx  
Installation  
Wall Stud  
Step 1 — Prepare the Mounting Surface  
Screws or  
Nails  
NOTE:  
Use a wall box with a depth of at least 3.0 inches (7.6 cm).  
Alternatively, the included mud ring (MR 200) can be used.  
For more information, see the full product user guides at  
www.extron.com. The installation must comply with the  
National Electric Code.  
Wall opening is  
flush with edge of box.  
a. Place the wall box against the installation surface and mark the  
Cable  
Clamp  
opening guidelines.  
T
LOCAL U  
TIP: Use a level to mark the opening.  
INPUTS  
R  
RS-2
D
Rx  
x
T
DVI-  
G
Rx  
Tx  
b. Cut out the material from the marked area.  
O
AUDI  
c. Secure the wall box with 10-penny nails or #8 or  
#10 screws, leaving the front edge flush with the surface.  
Signal Output  
Cable  
Extron  
DTP DVI 230 D  
d. Run all required cables (see steps 4, 5, and 6) and secure them with  
cable clamps.  
TIP: In order to fit the unit in the junction box, do not install  
Decora Faceplate  
boots on TP cables and RJ-45 connectors.  
Step 2 — Disconnect Power  
Disconnect all equipment power sources.  
Step 3 — Connect Inputs to the Transmitter  
A
B
C
DVI or HDMI input connector — Connect a DVI or HDMI cable between this port and the output port of the digital video source.  
Local output (DTP DVI 230 D only) — If desired, connect a DVI monitor for local monitoring of the input digital image.  
DDC Route DIP switch (DTP DVI 230 D only) — If the local output is not used,  
set the DDC Route DIP switch to remote. Ensure that you power the local display  
Connected RS-232  
and IR Device Pins  
Tx/Rx  
Pins  
Transmit pin on connected unit  
Receive pin on connected unit  
Ground  
Transmit pin on connected unit  
Receive pin on connected unit  
before powering the video source.  
D
E
Audio input — Connect an unbalanced stereo audio source to this 3.5 mm mini  
stereo jack.  
RS-232/IR Pass-Through connector — Plug an RS-232 or modulated IR device  
into the RS-232/IR Pass-Through port. Wire the cable as shown to the right.  
 

Edelbrock Automobile Parts TRX450R User Manual
Eiki Projector LC 6200 User Manual
Eizo Computer Monitor FlexScan F931 User Manual
Fisher Paykel Refrigerator E442BLXFD User Manual
Focal Portable Speaker 1000 Be User Manual
Frigidaire Electric Grill Electric Patio Grill User Manual
Fujitsu Speaker D5II User Manual
GE Air Conditioner AER05 User Manual
GE Drill 5GE752RB3A User Manual
GE Network Router A8950CC User Manual