PRESSURE WASHER
OWNER'S MANUAL
Model VPW42H
120V., 60 Hz., 12.5 Amps.
USA: EURO-PRO Operating LLC
94 Main Mill Street, Door 16
Plattsburgh, NY 12901
Canada: EURO-PRO Operating LLC
4400 Bois Franc
St. Laurent, QC H4S 1A7
Tel: 1 (800) 798-7398
TROUBLE SHOOTING
SAFETY & WARNING INSTRUCTIONS
PROBLEM
PRESSURE
POSSIBLE REASON
POSSIBLE SOLUTION
WARNING
WARNING
1. Check plug, socket, fuses,
breaker.
SERVICING OF A DOUBLE-
INSULATED APPLIANCE.
Equipment damage.
1. Electrical socket is faulty or
breaker has tripped.
2. Voltage is inadequate.
3. GFCI has tripped.
4. Power cord is not plugged
in.
WASHER WILL NOT
START WHEN THE
ON/OFF SWITCH IS
IN THE "ON"
• ALWAYS turn water supply "ON"
before turning the pressure washer
"ON". Running pump dry causes
serious damage.
• Do not operate the pressure washer
with the inlet water screen removed.
Keep screen clear of debris and
sediment.
• NEVER operate pressure washer
with broken or missing parts. Check
equipment regularly and repair or
replace worn or damaged parts
immediately.
• Use only the nozzle supplied with this
machine.
• Never leave the lance unattended
while the machine is running.
• Never attempt to alter factory settings.
Altering factory settings could damage
the unit and will void the warranty.
• Always hold gun and lance firmly when
starting and operating the machine.
• NEVER allow the unit to run with the
trigger released (OFF) for more than
one minute. Resulting heat buildup
will damage pump.
2. Check that the voltage is
adequate.
In a double-insulated product, two
systems of insulation are provided
instead of grounding. No grounding
means are provided for a double-
insulated product, nor should grounding
means be added to the product.
Servicing a double-insulated product
requires extreme care and knowledge
of the system and should be done only
by qualified service personnel.
Replacement parts for a double-
insulated product must be identical to
the original parts. A double-insulated
product is marked with the
3. Reset/Try another electrical
outlet.
4. Plug in power cord.
POSITION
1. Remove and clean water
intake filter.
1. Water intake filter is
clogged.
PUMP DOESN'T
REACH ADEQUATE
PRESSURE OR
CAVITATES
2. Tighten connections/bleed
system.
2. Pump is drawing air.
3. Diameter of garden hose is
too small.
3. Replace with 3/4 inch
garden hose.
4. Water supply is restricted.
4. Check hose for kinks or
leaks, open tap fully.
words " double Insulation"
or "Double Insulated".
1. Turn unit and water supply
off/Bleed system/Hold
trigger down. Allow water to
flow through the pump for
30 seconds.
2. Check hose for kinks or
leaks, open tap fully.
Product may also be
PRESSURE
WASHER HAS OR
WILL NOT
MAINTAIN
PRESSURE
marked with symbol shown.
1. Excessive air in waterline
and pump.
2. Water supply is restricted.
WARNING
Do not use pressure that exceeds the
operating pressure of any of the parts
(hoses, fittings, etc.) in the pressurized
system. Ensure that all equipment and
accessories are rated to withstand the
maximum working pressure of the unit.
PRESSURE
WASHER MAKES
EXCESSIVE NOISE
1. Air intake is blocked.
2. Water intake filter is dirty.
1. Clean the air intake vents.
2. Check & clean filter.
• NEVER store the pressure washer
outdoors or where it could freeze. The
pump will be seriously damaged.
• Release trigger when changing from
high to low pressure modes. Failure to
do so could result to damage to the
nozzle.
MOTOR DOES NOT
RUN
CONTINUOUSLY
WHEN TRIGGER IS
SQUEEZED/
MOTOR BUZZES
WHEN TURNED ON
BUT DOES NOT
START/MOTOR
STOPS RUNNING
WHILE UNIT IS IN
USE
WARNING
Explosion hazard.
• NEVER spray flammable liquids or
use pressure washer in areas
containing combustible dust, liquids
or vapors.
• NEVER operate this machine in a
closed building or in or near an
explosive environment.
1. Net voltage is lower than
suggested.
1. Check that the voltage is
adequate.
• This unit must always be used in the
horizontal position.
CAUTION
WARNING
Keep hose away from sharp objects.
Bursting hose may cause injury. Examine
hoses regularly and replace if damaged.
Do not attempt to mend a damaged hose.
• Do not spray electrical apparatus or
wiring.
• NEVER disconnect the high pressure
discharge hose from the machine while
the system is pressurized. To
depressurize the machine, turn the
power and water supply off, then press
the gun trigger 2-3 times.
• NEVER permanently engage the trigger
mechanism on the gun.
• NEVER operate the machine without all
the components properly connected to
the unit (handle, gun/lance assembly,
9
2
nozzle, etc.).
OPERATING INSTRUCTIONS
SAFETY & WARNING INSTRUCTIONS
Maintenance & Cleaning
Winterizing & Long Term Storage
EXTENSION CORDS
WARNING
Lubrication: The pressure washer is
supplied with a closed lubrication system,
so no addition of oil is needed.
1. Disconnect all water connections.
2. Turn the pressure washer on for a
few seconds, until any remaining
water in the pump exits.
3. Turn the unit off immediately.
4. Store the pressure washer, parts and
accessories in an area with a
DANGER
When using the pressure cleaner, use
If using an extension cord, use only
safety equipment including protective
Checking the Water Intake Filter: The
water intake filter is located inside the water
intake connector. (Fig. 10). Remove
periodically and inspect for any deposits
that might accumulate there.
grounded, three wire extension cords that
clothing and safety goggles.
are in good condition. Use only extension
cords that are intended for outdoor use.
These extension cords are identified by a
temperature above 32°F.
Motor Thermostat
WARNING
marking "Acceptable for use with outdoor
appliances; store indoors while not in
Do not use acids, solvents, or any other
use." use only extension cords having an
Important: This pressure washer is
equipped with a motor thermostat. The
motor will stop if it is overheating. Wait
20-30 minutes before starting the unit
again. If it stops again, please call
customer service at 1 (800) 798-7398.
flammable material in this product. These
products can cause physical injuries to the
operator and irreversible damage to the
machine.
electrical rating not less than the product.
Do not use damages extension cords.
Examine extension cord before using and
replace if damaged. Do not abuse
Hose Connector
Water Intake
Fig. 10
extension cord and do not pull on the
cord to disconnect. Keep cord away from
heat and sharp edges. Always disconnect
from the receptacle before disconnecting
the product from the extension cord.
Note: Do not use 16 or 18 AWG
Cleaning the Nozzles: If you notice that the
output pressure fluctuates, you may have to
clean the nozzles. Turn the unit "Off". Unplug
from electric outlet and disconnect the water
supply. Remove the lances, trigger gun and
hose from unit. Take the small metal pin
provided and insert into the nozzle end to
remove any obstructions. (Fig. 11)
WARNING
Ground Fault Circuit Interrupter
(GFCI)
• Never use the pressure cleaner to
draw in water contaminated with
solvents, e.g. paint thinners,
This unit is equipped with a Ground
Fault Circuit Interrupter (GFCI) built into
the plug. This device provides additional
protection from the risk of electrical
shock. When connecting the GFCI to the
electrical outlet, the indicator should
appear red. If the indicator is not red,
depress the RESET button on the GFCI
until the indicator appears red.
extension cords on this product.
gasoline, oil, etc.
• Always prevent debris from being
drawn into the unit by suing a clean
water source.
• Always grip the gun firmly before
pressing the trigger, to counteract the
recoil when starting.
• Always discharge residual pressure
before disconnecting the hose.
• To ensure the appliance safety, use
only original spare parts from the
manufacturer, or approved by the
manufacturer.
• Always hold the trigger and lance
with two hands and keep a tight grip.
• Always keep the filter clean. If you
are in a high mineral area, check with
the water supply company whether
you should use additional filters
before using the pressure cleaner.
DANGER
Failure to follow these instructions can
result in serious injury, including death.
Fig. 11
Cleaning Tips
WARNING
Wood Decks: Rinse deck and
surrounding area with fresh water. If
using detergent, fill the detergent
This will occur more frequently if your
water supply is very hard.
To reduce the risk of electrocution, keep
all connections dry and off the ground. Do
not touch the plug with wet hands.
applicator bottle and apply to the area
being cleaned. For optimal results,
reduce your work area to small sections
and clean each section one at a time.
Allow the detergent to rest on the surface
for a few minutes and then rinse at high
pressure. Do not let the detergent dry on
the deck. Always clean from left to right
and top to bottom for best results. Rinse
at high pressure using the fan jet keeping
the tip of the spray nozzle 8-12 inches
from the surface. Caution: For soft
woods, increase the distance from the
cleaning surface.
Cars, Boats, & Motorcycles: Wet down
area to be cleaned before applying
detergent with clean water. Fill the
detergent applicator bottle and apply to
the area being cleaned. To achieve best
results, clean one side at a time. Allow
the detergent to rest on the surface for a
few minutes but do not let it dry. Rinse at
high pressure using the fan jet in a
sweeping motion keeping the tip of the
spray nozzle at least 8-10 inches away
from the surface. Maintain a further
distance when using a direct spray. Wipe
surface for a polished finish.
Storing Your Pressure Washer
When you have finished using your
pressure washer, follow these steps for safe
storage:
1. Turn the pressure washer to the "Off"
position.
Allowable Length
Extension Cord
25 '
50 ’
14 AWG
12 AWG
YES
NO
2. Turn off the water supply.
3. Before disconnecting the high pressure
hose connection, point the trigger gun in
a safe direction away from you and
discharge the high pressure water.
Disconnect the high pressure hose from
the pressure washer and trigger gun.
4. Disconnect garden hose from pressure
washer.
5. Remove excess water from the pump by
tipping the unit on both sides to drain
any remaining water from the water
intake and outlet fittings.
YES
YES
WARNING
When an extension cable is required, you
must ensure that it has the right ampere
rating for your pressure cleaner and is in
safe electrical condition.
6. Drain detergent tank and flush with clean
water.
7. Wipe away any remaining water on all
parts and fittings.
8. Engage the trigger gun safety lock.
9. Store the unit and accessories in a room
above 32°F.
3
8
OPERATING INSTRUCTIONS
GETTING TO KNOW YOUR PRESSURE WASHER
Using Detergent with the Pressure
Washer
CAUTION
Rear View
The soap dispenser may only be used
with the trigger gun.
When you wish to stop using the
pressure washer temporarily, make sure
that the safety lock has been engaged to
avoid any accidental operation. (Fig. 6)
15
Add detergent to the bottle and then
attach the detergent applicator bottle to
the high pressure lance, just push it
firmly onto the end of the trigger gun
and turn clockwise to lock in place.
(Fig. 9) To remove the detergent
applicator bottle, lift the tab on the top
of the connector and pull off.
Safety
Lock
Fig. 6
Using the Adjustable Lance
The angle of the water on the lance may
be adjusted between 0° and 60° by
turning the nozzle adjuster counter-
clockwise for a wider angle or clockwise
for a narrower angle. (Fig. 7) Always
make sure that the "On/Off' switch is in
the "Off" position before changing the
angle of the water jet. It is also
recommended that the trigger gun safety
lock be engaged as well. The adjustable
lance allows you to use any variety of
spray pattern from a full fan spray to a
direct stream spray. When using the
pressure washer to clean wood decks,
siding, vehicles, etc., always start using
the fan spray and begin spraying from a
minimum 36" away to avoid damaging
the surface of the material that you are
cleaning. Always clear the area that you
will be cleaning of people, pets and
objects.
Fig. 9
WARNING
3
3
15
Do not use acids, solvents, or any other
flammable material in this product. These
products can cause physical injuries to the
operator and irreversible damage to the
machine.
TOTAL STOP SYSTEM
PLEASE NOTE: This pressure washer is
equipped with the Total Stop System,
which stops the unit during the bypass
stage. To start the pressure washer, it is
therefore necessary to set the On/Off
switch to the “On” position; after that
press the trigger: the Total Stop System
will start the machine and will stop it
automatically when the trigger is
released. It is advisable to put on the
safety lock of the trigger whenever the
machine is stopped in order to avoid
unintentional starting.
1. Water Output
2. Water Inlet
3. Accessory Storage
4. Handle
5. On/Off Switch
6. Brush
7. Soap Dispenser
8. Adjustable Lance
9. Trigger Gun
10. Safety Trigger Lock
11. Trigger
12. High Pressure
Hose Connector
13. High Pressure Hose
14. Garden Hose Coupling
15. Power Cord Storage
* Illustrations may differ somewhat from actual product.
Any automatic start of the machine
without pressing the trigger is attributable
to air bubbles in the water or other similar
phenomena which do not imply the
existence of any defects in the machine.
Do NOT leave the appliance unattended
during the standby for more than 5
minutes. Contrarily, for the safety of the
appliance it is necessary to re-turn the
On/Off switch to the “Off” position. Please
check that the coupling of the high
pressure hose with the appliance and the
trigger gun supplied as standard
Fig. 7
Using the Brush
Technical Specifications
The brush is used with the trigger gun.
Push the brush onto the trigger gun
nozzle and turn clockwise to lock as
you would for the lance. The brush may
be used for washing cars, boats,
windows and other similar items. The
brush operates at open orifice pressure
so that it will not direct a stream of
water. (Fig. 8)
Voltage:
Power:
120V., 60Hz.
12.5 Amps
Pressure:
1500 psi. (max)
equipment is made correctly, that is to
say without any water leak.
Fig. 8
7
4
OPERATINGINSTRUCTIONS
OPERATING INSTRUCTIONS
Suitable Use of Your Pressure
Washer
Unpacking Your Pressure Washer
Attaching High Pressure Hose to
Pressure Washer
1. While facing the front of the unit
attach the high pressure hose to the
high pressure output connector on
the front side of the unit. Twist on
securely to avoid leakage. (Fig. 2)
Garden Hose Connection
After you open the package, check to
make sure that all the parts are in the box
as per parts that are illustrated on page 3
of this guide. Due to transport and packing
restraints, some accessories may be
supplied unassembled; in this case follow
the assembly instructions in this manual. If
you have any questions, call customer
service at 1 (800) 798-7398. Keep all
small and potentially harmful parts of the
packaging (plastic bags, foamed
Once all the desired attachments and
the high pressure hose are attached to
the pressure washer, you can connect
the garden hose to the unit.
1. Make sure that the water intake filter
is inside the water intake inlet.
(Fig. 5)
2. Attach the male adapter (supplied)
to the water intake connector on the
front side of the unit. (Fig. 5)
3. Attach the female hose coupling to
the garden hose. (Fig. 5)
4. Connect the female hose coupling
to the male adapter making sure
that it is secured in place.
This high pressure washer is suitable for
non-professional use. The working
temperature must range between 40°F
and 120 °F. The machine is supplied with
a trigger gun, equipped with a trigger
handle to offer a comfortable working
position.
The high pressure washer is suitable for
washing with cold water only. The water
that you use for the pressure washer
must not be dirty, sandy or contain any
corrosive chemical products.
The pressure washer may be used to
wash shutters, doors, tiles, cars, decks,
campers, etc., where high water pressure
is necessary to remove dirt.
With the detergent tank, the pressure
washer can be used to apply a thick
coating of aerated detergent to the areas
being cleaned .
polystyrene, nails, etc.) out of the reach of
children.
Correct Use of the Pressure
Washer
High Pressure
Output
(Lower Connector)
(Fig. 5)
Fig. 2
• Place the pressure washer in a safe
area and on a horizontal surface.
• When using the pressure washer,
hold the trigger gun firmly with one
hand on the handle and the other on
the lance. (Fig. 1)
Water inlet
2. Then ensure that the other end of the
high pressure hose is fastened
securely to the trigger gun. (Fig. 3)
Garden hose
(not supplied)
When using the pressure washer we
recommend the use of personal safety
items to reduce the risk of accidental
injury.
Fig. 5
Fig. 3
3. Once the high pressure hose is
connected to the trigger gun, you can
attach the lance, brush or soap
dispenser accessories. To attach
either the lance or the brush to the
trigger gun, hold the trigger gun in
your left hand insert the desired
accessory and push it in all the way
into the connector on the trigger gun
and turn it clockwise 60° until it locks
in place. To remove the attachment,
push down on the attachment and
turn counter-clockwise 60° and then
pull out. Make sure that the
Hose
connector
Garden hose
coupling
Fig. 1
4. After all the connections have been
made and BEFORE you plug the
pressure washer into an electrical
outlet, open the water supply and
press on the trigger switch in order to
remove any air which may be in the
hose or pump. Continue to press on
the trigger switch until you get a
constant flow of water coming out of
the trigger gun. Allow water to flow
for 30 seconds.
• NEVER point the water jet at electric
wiring, at the pump unit, or at any
person or animal.
attachments are securely locked in
place before use. (Fig. 4)
5. Once this is accomplished, release
the trigger switch. Engage the safety
lock on the trigger
Fig. 4
6. Ensure that the "On/Off" switch, at
the side of the unit, is on the "Off"
position, then plug the unit into an
electrical outlet and turn the unit to
the "On" position.
7. Now you are ready to use the
pressure washer. Disengage the
safety lock and depress the trigger on
the trigger gun.
5
6
|